Home
Administrator Guide
Learn about Synergis Cloud Link hardware and software.
Integration-specific configuration
Learn how to configure third-party devices to work with your Synergis Cloud Link unit.
Axis controllers
Reader connections on the AXIS A1001 controller
Each AXIS A1001 controller supports up to two readers, called Reader 1 and Reader 2 in Security Center Config Tool. The readers can use either Wiegand (default) or OSDP protocol. For OSDP, the reader must be wired to the first set of reader data A-/B+.

Release Notes
Learn about the Synergis Cloud Link release.
Hardware Installation Guide
Learn how to install and connect your Synergis Cloud Link appliance.
Administrator Guide
Learn about Synergis Cloud Link hardware and software.
- Preface
- Introduction
- General configuration
  Learn how to configure your Synergis Cloud Link unit.
- Integration-specific configuration
  Learn how to configure third-party devices to work with your Synergis Cloud Link unit.
  - Allegion Schlage wireless locks
  - ASSA ABLOY Aperio-enabled locks
  - ASSA ABLOY IP locks
  - AutoVu SharpV cameras
  - Axis controllers
    - Enrolling Axis controllers on the Synergis unit
      For the Synergis™ unit to communicate with Axis controllers, you must enroll the controllers using either the Synergis™ Appliance Portal or Config Tool.
    - Configuring Axis controller peripherals
      To configure the input contacts, output relays, and readers attached to the Axis controller, you must make your changes in Config Tool and the Synergis™ Appliance Portal.
    - Configuring the auxiliary I/O ports on AXIS A1601 controllers
      You can configure the auxiliary I/O ports on AXIS A1601 controllers to be used as either inputs or outputs, using the Synergis™ Appliance Portal.
    - Reader connections on the AXIS A1001 controller
      Each AXIS A1001 controller supports up to two readers, called Reader 1 and Reader 2 in Security Center Config Tool. The readers can use either Wiegand (default) or OSDP protocol. For OSDP, the reader must be wired to the first set of reader data A-/B+.
    - Reader connections on the AXIS A1601 controller
      Each AXIS A1601 controller supports up to two readers, called Reader 1 and Reader 2 in Security Center Config Tool.
    - Enabling OSDP (Secure Channel) readers on AXIS A1601 controllers
      You can use OSDP with Secure Channel between the AXIS A1601 controller and their OSDP readers to ensure end-to-end encryption.
  - DDS controllers
  - HID VertX sub-panels
  - Mercury controllers
  - Allegion Schlage locks through Mercury
  - BEST Wi-Q locks through Mercury
  - SimonsVoss SmartIntego locks through Mercury
  - SALTO SALLIS wireless locks
  - OSDP devices connected to the Synergis Cloud Link RS-485 ports
  - STid readers using the SSCP protocol
- Maintenance and troubleshooting
  Learn how to troubleshoot issues and keep your Synergis Cloud Link unit up to date.
Glossary
Where to find product information
You can find our product documentation in the following locations:
Technical support
Genetec™ Technical Assistance Center (GTAC) is committed to providing its worldwide clientele with the best technical support services available. As a customer of Genetec Inc., you have access to TechDoc Hub, where you can find information and search for answers to your product questions.

Reader connections on the AXIS A1001 controller

2022-07-05

Each AXIS A1001 controller supports up to two readers, called Reader 1 and Reader 2 in Security Center Config Tool. The readers can use either Wiegand (default) or OSDP protocol. For OSDP, the reader must be wired to the first set of reader data A-/B+.

The following chart shows the set of connectors corresponding to the reader on the Axis controller.

Note: This pin chart only shows up if the Axis controller is disconnected to the Synergis™ unit.